White Rodgers 3046-5 Mercury Flame Sensors Instalační manuál stáhnout pdf

To prevent electrical shock and/or equipment

damage, disconnect electric power to system at

main fuse or circuit breaker box until installation

is complete.

Shut off main gas to heating system until installa-

tion is complete.

Label all wires prior to disconnection when ser-

vicing controls. Wiring errors can cause improper

and dangerous operation.

Following installation or replacement, follow ap-

pliance manufacturer’s recommended installa-

tion and/or service instructions to insure proper

operation.

CAUTION

WARNING

PART NO. 37-0613G

Replaces 37-0613F

9651

WHITE-RODGERS

FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY

BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE

PERSONAL INJURY AND/OR PROPERTY DAMAGE.

Type 3046

Automatic Pilots

INSTALLATION INSTRUCTIONS

These Pilots can be used with either A, B, or E series pilot

burners.

Pilot Burners are available in 14 port arrangements,

Bunsen and “Non-linting”, and with a wide choice of

mounting facilities.

Contact Action is SPST snap-action, close-on-rise.

Orifice fittings offer three different styles of connections

each available for the most used gases.

Timing: Contacts close approximately 60 seconds after

the pilot is ignited. Contacts open approximately 40

seconds after the flame is extinguished.

PRECAUTIONS

Operator: Save these instructions for future use!

SPECIFICATIONS

If in doubt about whether your wiring is millivolt, line, or low

voltage, have it inspected by a qualified heating and air

conditioning contractor, electrician, or someone familiar

with basic electricity and wiring.

Do not exceed the specification ratings.

All wiring must conform to local and national electrical

codes and ordinances.

This control is a precision instrument, and should be

handled carefully. Rough handling or distorting compo-

nents could cause the control to malfunction.

Do not use on circuits exceeding specified volt-

age. Higher voltage will damage control and could

cause shock or fire hazard.

These automatic pilots may be used with natural, manu-

factured, or mixed gases, and with LP gases where

means are provided for obtaining a 100% shutoff system.

The pilot burner should be equipped with the recom-

mended size orifice fitting.

The metal box containing the switch may be conveniently

mounted in any position. The cover is easily removed,

making the switch terminals readily accessible.

DESCRIPTION

Automatic pilots are required on gas-fired heating equip-

ment to prevent the flow of gas to the main burner if the

pilot flame is not burning or is insufficient to properly ignite

the main burner.

This pilot has automatic reset (automatic recycling) need-

ing merely relighting or possibly only the resumption of

proper gas pressure to put back in operation.

ATTENTION!

This product contains mercury. There will not be any exposure to mercury under normal conditions of use. This product may

replace a unit which contains mercury. Do not open mercury cells. If a cell becomes damaged, do not touch any spilled

mercury. Wearing nonabsorbent gloves, take up the spilled mercury with sand or other absorbent material and place into a

container which can be sealed. If a cell becomes damaged, the unit should be discarded. Mercury must not be discarded in

household trash. When this unit or the unit it is replacing is to be discarded, place in a suitable container and return to us .

WHITE-RODGERS DIVISION

EMERSON ELECTRIC CO.

9797 REAVIS RD., ST. LOUIS, MO. 63123-5398

(314) 577-1300, FAX (314) 577-1517

9999 HWY. 48, MARKHAM, ONT. L3P 3J3

(905) 475-4653, FAX (905) 475-4625

Printed in U.S.A.

1 2 3 4 5 6

Shrnutí obsahu

Strany 1 - Type 3046

To prevent electrical shock and/or equipmentdamage, disconnect electric power to system atmain fuse or circuit breaker box until installationis comple

Strany 2 - Bleed Burners are available

2To avoid personal injury and/or property damage,shut off gas and electric to heating system untilinstallation is complete.Uncoil the capillary carefu

Strany 3 - TESTING THE PILOT

3TOLINETHERMOSTATHIGHLIMITAUTOMATICPILOTSILENT KNIGHTGAS VALVEDiagram for “Silent Knight”valve with conduit connectorCONNECT TRANSFORMER HERE IF

Strany 4 - TYPE 3046

Veilleuses automatiquesTYPE 3046INSTRUCTIONS D’INSTALLATIONImprimé aux É.-U.ASI VOUS NE LISEZ PAS ATTENTIVEMENT CES INSTRUCTIONS AVANTD’INSTALLER ET D

Strany 5

2INSTALLATIONAfin de prévenir les blessures et les dommagesmatériels, coupez le gaz et l’électricité qui alimententle système de chauffage jusqu’à ce

Strany 6 - ALLUMAGE DE LA VEILLEUSE

3VÉRIFICATION DE LA VEILLEUSE3. Attendez environ cinq minutes, puis rallumez la veilleuseconformément aux directives de la section «Allumagede la veil

Komentáře k této Příručce

Žádné komentáře

White Rodgers 3046-5 Mercury Flame Sensors Instalační manuál

Procházejte online nebo si stáhněte Instalační manuál pro ne White Rodgers 3046-5 Mercury Flame Sensors. White Rodgers 3046-5 Mercury Flame Sensors Installation Instructions Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro ne White Rodgers 3046-5 Mercury Flame Sensors