White Rodgers 668-501 Kwik-Sensor CAD Cell Relays Instalační manuál stáhnout pdf

Printed in U.S.A.

PART NO. 37-5456A

Replaces 37-1794 &

37-9517

9510

TYPE 668

Intermittent Ignition* – Non Recycling

OIL BURNER CONTROL

With Series 956 Flame Detector

INSTALLATION INSTRUCTIONS

Operator: Save these instructions for future use!

WHITE-RODGERS DIVISION

EMERSON ELECTRIC CO.

9797 REAVIS RD., ST. LOUIS, MO. 63123

(314) 577-1300, Fax (314) 577-1517

9999 HWY. 48, MARKHAM, ONT. L3P 3J3

(905) 475-4653, FAX (905) 475-4625

DESCRIPTION

FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY BEFORE

INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL

INJURY AND/OR PROPERTY DAMAGE.

The proper Location and Mounting of the primary oil

burner control panel on the burner and the flame detector

with respect to the oil flame shall be determined by the

furnace, boiler, or burner manufacturer.

If this control, supplied as part of a furnace, boiler or

burner, is wired to the equipment or if the manufacturer

of such equipment provides instructions for wiring this

* Formerly called constant ignition.

SPECIFICATIONS

Electrical Data

Input voltage: 668 120V. AC, 60Hz.

668H 220V. AC, 50/60Hz.

Maximum Load Current:

Oil Burner Motor (Orange Wire):

10 Amps F.L. 60 Amps L.R.

Ignition Transformer:

360VA (3.0 Amps)

Relay Voltage: 668 24 Volts AC, 60Hz.

668H 24 Volts AC, 50/60Hz

Room Thermostat:

Set adjustable heat anticipator at 0.4 Amps. For fixed

anticipation thermostats, use 0.35 to 0.45 Amp.

heater.

Safety Timing:

668, 668H-401 to 499: 45 seconds

668, 668H-501 to 599: 30 seconds

668, 668H-601 to 699: 15 seconds

INSTALLATION AND WIRING

control, then follow his recommendations. If no special

wiring instructions are given, then follow the electrical

connections shown on this diagram for a simple system.

For more complicated systems, especially for hot water

heating, consult the manufacturer of the heating plant for

full details of the desired sequence of control operation.

To prevent electrical shock and/or equipment

damage, disconnect electric power to system, at

main fuse or circuit breaker box, until installation

is complete.

Do not use on circuits exceeding specified volt-

ages. Higher voltages will damage control and

could cause shock or fire hazard.

If in doubt about whether your wiring is millivolt, line, or

low voltage, have it inspected by a qualified heating and

air conditioning contractor, electrician, or someone famil-

iar with basic electricity and wiring.

Do not exceed the specification ratings.

All wiring must conform to local and national electrical

codes and ordinances.

This control is a precision instrument, and should be

handled carefully. Rough handling or distorting compo-

nents could cause the control to malfunction.

CAUTION

PRECAUTIONS

WARNING

WHITE-RODGERS

The type 668 Oil Burner Control provides safe operation

of oil burners on heating plants where ignition during the

entire burner cycle is desired.

The 668 is used with the 956 Flame Detector

1 2 3 4 5 6

Shrnutí obsahu

Strany 1 - WHITE-RODGERS

Printed in U.S.A.PART NO. 37-5456AReplaces 37-1794 &37-95179510TYPE 668Intermittent Ignition* – Non RecyclingOIL BURNER CONTROLWith Series 956 Fla

Strany 2 - External Line Voltage Wiring

2Possible Cause of CorrectionTroubleOpen circuit in Cell Replace Cell (or Cell Assembly)of 956 Flame Detector. Do notdisturb position of bracket orsoc

Strany 3 - TESTING CONT

34. If safety lockout problem is of an occasional naturethe following additional check may be made toinsure that flame detector location is not a marg

Strany 4

WHITE-RODGERSImprimé aux États-UnisNo de pièce 37-5456ARemplace : 37-1794 &37-95179510Utilisateur : conservez ces instructions pour vous y référer

Strany 5 - AVERTISSEMENT

2Une fois l’installation complétée, il est recommandé de mettrele système à l’essai pour s’assurer de son bon fonctionnement.1. Ouvrez l’interrupteur

Strany 6 - ESSAIS (SUITE)

3ESSAIS (SUITE)d. Si la résistance du détecteur dépasse 1000 ohms, ilest possible que celui-ci ne détecte pas très bien laflamme du brûleur. Vérifiez

Komentáře k této Příručce

Žádné komentáře

White Rodgers 668-501 Kwik-Sensor CAD Cell Relays Instalační manuál

Procházejte online nebo si stáhněte Instalační manuál pro Detektory kouře White Rodgers 668-501 Kwik-Sensor CAD Cell Relays. White Rodgers 668-501 Kwik-Sensor CAD Cell Relays Installation Instructions [zh] Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Detektory kouře White Rodgers 668-501 Kwik-Sensor CAD Cell Relays