White-rodgers 1F80-240 Uživatelský manuál stáhnout pdf

1F80-240

(for HEATING ONLY systems)

Programmable Electronic Digital Thermostat

INSTALLATION AND

OPERATION INSTRUCTIONS

FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY

BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE

PERSONAL INJURY AND/OR PROPERTY DAMAGE.

DESCRIPTION

• Heat program storage

• Backlit display

• Temperature override until next program period

• Manual program override (HOLD temperature)

• Temporary HOLD

• °F/°C convertibility

• Temperature range 45° to 90°F

• RH, W, and G terminals

• Battery powered

• 2 “AA” Energizer

alkaline batteries included

Operator: Save these instructions for future use!

Your new White-Rodgers 5-Day/1-Day/1-Day Digital Thermo-

stat uses the technology of a solid-state microcomputer to

provide precise time/temperature control. This thermostat offers

you the flexibility to design a heating program that fits your needs.

Features:

• Separate 5-day (weekday), 1-day (Sat) and 1-day (Sun) pro-

gramming with four separate time/temperature periods per day

• Preprogrammed temperature control

• LCD continuously displays set point, and alternately dis-

plays time and room temperature

PRECAUTIONS

This thermostat is intended for use with a low voltage system; do

not use this thermostat with a line voltage system. If in doubt

about whether your wiring is millivolt, line, or low voltage, have

it inspected by a qualified heating and air conditioning contractor

or electrician.

Do not exceed the specification ratings.

All wiring must conform to local and national electrical codes and

ordinances.

This control is a precision instrument, and should be handled

carefully. Rough handling or distorting components could cause

the control to malfunction.

▲

! CAUTION

To prevent electrical shock and/or equipment damage,

disconnect electric power to system at main fuse or

circuit breaker box until installation is complete.

▲

! WARNING

Do not use on circuits exceeding specified voltage.

Higher voltage will damage control and could cause

shock or fire hazard.

Do not short out terminals on gas valve or primary

control to test. Short or incorrect wiring will damage

thermostat and could cause personal injury and/or

property damage.

Thermostat installation and all components of the

system shall conform to Class II circuits per the NEC

code.

SPECIFICATIONS

ELECTRICAL DATA

Electrical Rating:

8 to 30 VAC 50/60 Hz. or D.C.

0.05 to 1.0 Amps (Load per terminal)

1.5 Amps Maximum Total Load (All terminals combined)

THERMAL DATA

Setpoint Temperature Range:

45°F to 90°F (7°C to 32°C)

Operating Ambient Temperature Range:

32°F to 105°F

Operating Humidity Range:

0 to 90% RH (non-condensing)

Shipping Temperature Range:

-4°F to 150°F

APPLICATIONS

For use with:

• Standard heat only systems

• Electric heat systems

• Gas or oil fired systems

• Gas systems with intermittent ignition devices (I.I.D.)

and/or vent dampers

• Hydronic (hot water or steam) systems

• Single-stage heat pump systems (no auxiliary heat)

• Millivolt systems

DO NOT USE WITH:

• Multi-stage systems

• Systems exceeding 30 VAC and 1.5 amps

• 3-wire zoned hydronic heating systems

• Heat pump systems

Printed in U.S.A.

PART NO. 37-6325B

0148

WHITE-RODGERS

EMERSON ELECTRIC CO.

9797 REAVIS ROAD

ST. LOUIS, MISSOURI 63123-5398

www.white-rodgers.com

1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - 1F80-240

1F80-240(for HEATING ONLY systems)Programmable Electronic Digital ThermostatINSTALLATION ANDOPERATION INSTRUCTIONSFAILURE TO READ AND FOLLOW ALL INSTR

Strany 2 - INSTALLATION

2MountingholesMountingholesElectric/GasswitchScrew anchorsINSTALLATIONREMOVE OLD THERMOSTAT1. Shut off electricity at the main fuse box until installa

Strany 3 - Heating System

3Heating System1. Move SYSTEM switch to HEAT position. If the heatingsystem has a standing pilot, be sure to light it.2. Press to adjust thermostat

Strany 4 - OPERATION

4Before you begin programming your thermostat, you should befamiliar with its features and with the display and the locationand operation of the therm

Strany 5 - PROGRAMMING YOUR THERMOSTAT

51Step Press Button(s) Displayed (Factory Default) Press or to select: COMMENTSHOLD(0:00)0 to 8 hrs (in 15 minute increme

Strany 6 - CHECK YOUR PROGRAMMING

6Enter Heating Program1. Move the SYSTEM switch to HEAT.2. Press PRGM once. “MO TU WE TH FR” (indicating weekdayprogram) will appear in the display. A

Strany 7 - TROUBLESHOOTING

7Symptom Possible Cause Corrective ActionNo Heat/No Fan 1. Blown fuse or tripped circuit breaker. Replace fuse or reset breaker.(common problems) 2. F

Strany 8

For additional product information, visit www.white-rodgers.com

Komentáře k této Příručce

Žádné komentáře

White-rodgers 1F80-240 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Kontrolní panel White-rodgers 1F80-240. White Rodgers 1F80-240 User Manual Uživatelská příručka

Shrnutí obsahu

Komentáře k této Příručce

Související produkty a manuály pro Kontrolní panel White-rodgers 1F80-240